You copied the Doc URL to your clipboard.

LDM

Load Multiple registers.

Syntax

LDM{addr_mode}{cond} Rn{!}, reglist{^}

where:

addr_mode

is any one of the following:

IA
Increment address After each transfer. This is the default, and can be omitted.
IB
Increment address Before each transfer (A32 only).
DA
Decrement address After each transfer (A32 only).
DB
Decrement address Before each transfer.

You can also use the stack oriented addressing mode suffixes, for example, when implementing stacks.

cond
is an optional condition code.
Rn
is the base register, the AArch32 register holding the initial address for the transfer. Rn must not be PC.
!
is an optional suffix. If ! is present, the final address is written back into Rn.
reglist
is a list of one or more registers to be loaded, enclosed in braces. It can contain register ranges. It must be comma separated if it contains more than one register or register range. Any combination of registers R0 to R15 (PC) can be transferred in A32 state, but there are some restrictions in T32 state.
^

is an optional suffix, available in A32 state only. You must not use it in User mode or System mode. It has the following purposes:

  • If reglist contains the PC (R15), in addition to the normal multiple register transfer, the SPSR is copied into the CPSR. This is for returning from exception handlers. Use this only from exception modes.
  • Otherwise, data is transferred into or out of the User mode registers instead of the current mode registers.

Restrictions on reglist in 32-bit T32 instructions

In 32-bit T32 instructions:

  • The SP cannot be in the list.
  • The PC and LR cannot both be in the list.
  • There must be two or more registers in the list.

If you write an LDM instruction with only one register in reglist, the assembler automatically substitutes the equivalent LDR instruction. Be aware of this when comparing disassembly listings with source code.

You can use the --diag_warning 1645 assembler command line option to check when an instruction substitution occurs.

Restrictions on reglist in A32 instructions

A32 load instructions can have SP and PC in the reglist but these instructions that include SP in the reglist or both PC and LR in the reglist are deprecated.

16-bit instructions

16-bit versions of a subset of these instructions are available in T32 code.

The following restrictions apply to the 16-bit instructions:

  • All registers in reglist must be Lo registers.
  • Rn must be a Lo register.
  • addr_mode must be omitted (or IA), meaning increment address after each transfer.
  • Writeback must be specified for LDM instructions where Rn is not in the reglist.

In addition, the PUSH and POP instructions are subsets of the STM and LDM instructions and can therefore be expressed using the STM and LDM instructions. Some forms of PUSH and POP are also 16-bit instructions.

Loading to the PC

A load to the PC causes a branch to the instruction at the address loaded.

Also:

  • Bits[1:0] must not be 0b10.
  • If bit[0] is 1, execution continues in T32 state.
  • If bit[0] is 0, execution continues in A32 state.

Loading or storing the base register, with writeback

In A32 or 16-bit T32 instructions, if Rn is in reglist, and writeback is specified with the ! suffix:

  • If the instruction is STM{addr_mode}{cond} and Rn is the lowest-numbered register in reglist, the initial value of Rn is stored. These instructions are deprecated.
  • Otherwise, the loaded or stored value of Rn cannot be relied on, so these instructions are not permitted.

32-bit T32 instructions are not permitted if Rn is in reglist, and writeback is specified with the ! suffix.

Correct example

    LDM     r8,{r0,r2,r9}      ; LDMIA is a synonym for LDM

Incorrect example

    LDMDA   r2, {}         ; must be at least one register in list
Was this page helpful? Yes No